TECHNYL® SLIDE A 216 Y10 NC
Low Friction Wear-Resistant PA66 · Ideal for Sliding Components · Asia Availability Only
Wear Modified
Medium Viscosity
Asia Only
TECHNYL® SLIDE A 216 Y10 NC is an unreinforced polyamide 66 (PA66) grade with medium viscosity, heat stabilized, and specially modified to have improved frictional properties for injection molding. This grade offers all the primary properties of unreinforced PA66 and mainly has excellent surface properties such as low coefficient of friction and good resistance to wear. This product is available only in Asia.
📋 Product Overview
- Polymer Type: PA66 (Polyamide 66)
- Reinforcement: Unreinforced
- Friction Properties: Low coefficient of friction, good wear resistance
- Viscosity: Medium Viscosity
- Heat Stabilized: Yes
- Processing: Injection Molding
- Color: Natural
- Availability: Asia Only
- Certifications: RoHS, REACH
- Typical Applications: Consumer goods, Pulleys, Industrial applications
📊 Technical Data Sheet
Physical Properties
Mechanical Properties (DAM)
Thermal Properties
Flammability
🔄 Low Friction & Wear Resistance · Ideal for Sliding Components
TECHNYL® SLIDE A 216 Y10 NC is specially modified to offer excellent frictional properties:
- Low Coefficient of Friction: Excellent surface sliding performance, reduces energy loss in moving parts
- Good Wear Resistance: Extends service life of sliding components
- Retains PA66 Base Properties: Maintains mechanical and thermal properties of unreinforced PA66
- Heat Stabilized: Suitable for long-term use environments
⚙️ Processing Conditions
80°C / 2-4 hours
Dew point ≥ -20°C
0.2%
265 – 275°C
270 – 280°C
280 – 285°C
60 – 80°C
(Up to 120°C for high surface quality)
⚠️ Injection Advice
The material is supplied in airtight bags, ready for use. If the virgin material has absorbed moisture, it must be dried with dehumidified air drying equipment (dew point minimum -20°C). Recommended drying time: 2-4 hours.
For unfilled polyamides, DOMO recommends the use of high alloy steel with a low chromium content. For example: X38CrMoV5-1 (EN Norm) – 1.2367/1.2343 (DIN Norm).
🎯 Target Applications
Drive pulleys, guide wheels
Slides, sliders, bushings
Wear parts, transmission components
Sports equipment, office equipment components
📌 Note: This grade is available exclusively for the Asian market (including China, Japan, Korea, Southeast Asia, etc.). For other regions, please contact DOMO Chemicals for equivalent alternatives.
🌟 Key Advantages
- ✅ Low Coefficient of Friction: Excellent surface sliding performance, reduces friction loss
- ✅ Good Wear Resistance: Extends service life of sliding components
- ✅ Unreinforced Design: Retains good toughness and processability of PA66
- ✅ Medium Viscosity: Good flowability for complex mold designs
- ✅ Heat Stabilized: Long-term thermal aging resistance
- ✅ High HDT: 230°C at 0.45MPa
- ✅ Good Surface Quality: Suitable for applications with appearance requirements
- ✅ RoHS & REACH Compliant: Meets global environmental regulations
📌 Material Selection Guide
Disclaimer: The information provided in this documentation corresponds to our technical knowledge at the date of its publication and does not constitute a specification. DOMO cannot anticipate all conditions under which this information and our products may be used. Users are advised to make their own tests to determine the safety and suitability for their own purposes. Unless otherwise agreed in writing, DOMO sells the product without warranties. Unless specifically indicated, this grade is not suitable for pharmaceutical/medical applications.
Source: DOMO Chemicals Official Technical Data Sheet (TECHNYL SLIDE A 216 Y10 NC, Document 002251)
Last Updated: May 2026